Guide · Farmers · 3 min read · Updated 17 November 2026
Low Loader vs Beavertail vs Flatbed for Farm Machinery
Short answer
A beavertail lorry suits compact tractors, mini diggers and smaller implements up to around 10 tonnes. A semi-low loader or low loader is needed for large tractors, telehandlers and combines because its low deck keeps tall machines under bridge heights. Flatbeds suit implements lifted on by a loader. Prices range from £150 for an implement on a flatbed to £1,000 or more for a combine on a low loader.
Why the trailer matters
Picking the right vehicle is the most important decision in machinery transport. Too small and the load is overweight or overhangs the deck. Too tall and the machine will not clear bridges. Too big and you pay for capacity you do not need, and the lorry may not even fit through the farm gate.
Hauliers choose based on four numbers: the machine's weight, width, height and length. Ground clearance and how the machine loads, under its own power or by lifting, come next.
Ground clearance is easy to forget. A machine with a low-slung belly, such as some mowers or sprayers, can ground out on the crest of a steep beavertail. In that case a low loader with a shallower ramp angle, or a flatbed and a lift, may be the better option. Access at the two ends then settles the final choice, because an articulated vehicle needs far more room than a rigid lorry and some farmyards simply cannot take one.
| Vehicle | Best for | Guide price |
|---|---|---|
| Beavertail lorry | Compact and vintage tractors, small implements | £180–£350 local |
| Rigid plant lorry with ramps | Mid-size tractors 6–9 tonnes | £350–£750 regional |
| Semi-low loader | Large tractors, telehandlers | £600–£1,300 |
| Low loader | Combines and tall wide machines | from £1,000 |
| Flatbed | Implements loaded by telehandler | from £150 |
Beavertail lorries
A beavertail is a rigid lorry or trailer with a sloping rear section and folding ramps. Machines drive straight up the tail onto the deck. They are quick, need less space than an articulated vehicle and suit narrow lanes and tight farmyards.
Their limit is payload and deck height. The deck sits higher than a low loader's, so a tall tractor with a cab and exhaust stack may end up over safe bridge height. For a vintage Ferguson, a compact Kubota or a small loader tractor, a beavertail is ideal and usually the cheapest option.
Semi-low loaders and low loaders
A semi-low loader is an articulated trailer with a stepped deck, lower at the back where the machine sits, and ramps at the rear. It handles most large tractors and telehandlers comfortably. A full low loader goes further, with a well between the axles and the neck, sometimes with a detachable gooseneck so machines can drive on from the front.
Low loaders are the right choice for combines, self-propelled sprayers, foragers and anything where height is tight. They need more room to manoeuvre, so access at both ends has to be checked first.
- Low deck keeps tall machines within bridge clearance
- High payload for heavy tractors with weights
- Wide decks suit machines close to the width limit
- Need firm, open access for an articulated vehicle
- Usually needed when wide-load rules apply
Flatbeds and HIAB lorries
Many implements do not drive. Ploughs, drills, cultivators and mowers are often lifted onto a flatbed by a telehandler at each end. If no loader is available, a lorry with a HIAB crane can lift lighter implements on and off itself, provided the weight is within the crane's capacity at the reach needed.
Trailed equipment with its own wheels, such as balers or bale trailers, can sometimes go on a beavertail instead. Tell us how the implement will be loaded and whether there is a telehandler at both ends.
How we choose for your job
Send the make and model, measured width and height, the weight if known and photos of both access points. We match the vehicle to the machine and the route, then give one fixed price. If two vehicles would work, we quote the one that suits the access best, because a cheaper lorry that cannot reach the yard is no saving.
For mixed loads, such as a tractor plus implements, we pick a vehicle that carries the lot in one trip where weights and dimensions allow.
Securing the load
Whatever the trailer, the machine must be secured so it cannot move under braking, cornering or a sudden swerve. On machinery work that means chains and binders or heavy-duty ratchet straps, rated for the weight, attached to the axles, tow points or designated lashing points on the frame. Straps should never go over hydraulic hoses, through wheel rims where they can cut, or around plastic panels.
Tracked machines and those with rubber tyres can shift on a wet steel deck, so drivers often use timber packing or anti-slip mats under the tracks or tyres. Loose parts in the cab, buckets on a loader and pick-up hitches are tied down separately.
A good driver stops after the first few miles to check the chains and straps, because loads settle once moving. On long runs, they check again at each break.
Signs you have the wrong vehicle booked
If the quote does not mention the trailer type, ask. If the machine is close to four metres tall on paper and the vehicle offered is a beavertail, question it. If your gateway is under four metres wide and an articulated low loader is booked, discuss a roadside handover. These checks take minutes and avoid a wasted journey that someone will have to pay for.
Questions people also ask
What is a beavertail lorry?
A beavertail is a lorry or trailer whose rear section slopes down towards the ground, with ramps fitted at the end, so wheeled or tracked machines can drive straight on. It suits smaller tractors and plant and is quicker to load than most other trailers.
Does a telehandler need a low loader?
Most full-size telehandlers go on a semi-low loader because of their weight and height. Compact telehandlers can sometimes travel on a large beavertail. Give us the model, height to the top of the cab and weight so we can choose correctly.
Why is a low loader more expensive?
A low loader is an articulated combination with a specialist trailer and a more powerful tractor unit. It often carries loads that need route planning and wide-load notices, which takes time. For tall or heavy machines, though, it is the only safe and legal option.
Written and checked by the Farm Machinery Transport team. Read our editorial policy.
More guides
How Much Does Farm Machinery Transport Cost in the UK?
Farm machinery transport in the UK costs £180–£350 to move a compact or vintage tractor locally on a beavertail, £350–£750 for a 6–9 tonne tractor…
Moving a Combine Harvester by Road: UK Rules and Options
A combine harvester can be driven on UK roads within the agricultural vehicle rules or carried on a low loader. Driving suits short hops between…
How to Prepare a Tractor for Transport: A Checklist
To prepare a tractor for transport, remove dual wheels, front weights and loose items, lower and secure the three-point linkage, check it starts and…
Collecting Machinery from a Farm Auction or Dispersal Sale
After buying at a farm auction or dispersal sale, book haulage as soon as the hammer falls, because collection windows are short and lorries fill up…
Get a free farm machinery transport quote
Tell us what you need and we'll come back with a clear price.
Request a quote