Farm Machinery Transport

Guide · Farmers · 3 min read · Updated 17 November 2026

How to Prepare a Tractor for Transport: A Checklist

Short answer

To prepare a tractor for transport, remove dual wheels, front weights and loose items, lower and secure the three-point linkage, check it starts and brakes properly, and leave keys and any paperwork with it. Make sure the lorry can reach a firm, level loading point. A tractor that drives straight onto the trailer loads in under an hour and keeps the job within the quoted price.

How to Prepare a Tractor for Transport: A Checklist

Why preparation matters

Most delays on tractor moves come from things that could have been sorted the day before: duals still fitted, a flat battery, keys locked in the farm office or a lorry that cannot get past a soft gateway. Each one adds waiting time and, sometimes, a second visit.

A prepared tractor is also safer to load. Ramps are steep, decks can be slippery in rain, and a machine with an unknown brake fault or a stuck clutch is a real hazard on a beavertail. The checklist below covers what the driver needs from you.

It also protects the price. A fixed quote assumes the tractor is ready when the lorry arrives and can be loaded in the normal time. If the driver has to wait while duals are unbolted or a battery is charged, that time has to come from somewhere, and on a busy day it can mean the lorry misses its next job. Half an hour of preparation the evening before is the cheapest part of any machinery move, and it is the part entirely in your control.

The tractor itself

Start with width and weight. Dual wheels make most tractors too wide for a standard trailer, so take them off. Front weight blocks add weight and length and can foul the ramps, so remove them unless they are part of the sale. Lower the rear linkage, take off any drawbar or pick-up hitch that sticks out, and fold mirrors in.

Check that it starts, steers and brakes. Leave a reasonable amount of fuel, enough to drive on and off, but there is no need for a full tank. If the tractor does not run, tell us when booking, because a winch-equipped vehicle will be needed.

  • Remove dual wheels and front weights
  • Lower and secure the three-point linkage
  • Take off loose tools, cab clutter and anything that can blow away
  • Close the cab doors and rear window and secure the roof hatch
  • Fold mirrors and remove beacons if they add height
  • Check brakes, steering and battery the day before

Measurements to give when booking

Accurate dimensions decide the trailer. The make and model is a good start, but tyres, cabs and options change the numbers. Measure the overall width across the widest point of the tyres, the height to the top of the cab or exhaust, and the length including any linkage arms. A rough weight from the manual or the dealer is enough.

These figures tell us whether a beavertail is enough, whether a semi-low loader is needed to stay under bridge heights, and whether any wide-load rules apply.

MeasurementWhere to measureWhy it matters
WidthOutside of widest tyresTrailer choice and wide-load rules
HeightGround to top of cab or exhaustBridge clearance on the trailer
LengthFront weights to linkage armsDeck length and overhang
WeightManual, dealer or weighbridgeTrailer payload and axle limits

Access and the loading point

Walk the route the lorry will take from the road. Look for gateway width, overhanging branches, low cables and soft ground. A rigid beavertail needs less room than an articulated low loader, but both need a firm, level surface to drop ramps on, ideally concrete or hardcore.

If the yard is muddy, consider bringing the tractor to the roadside or a hard standing area at an agreed time. That one step often prevents the most expensive problem in machinery haulage, which is a lorry bogged down in a field entrance.

Paperwork and handover

For dealer, auction or private sales, have the sale paperwork and the V5C where the tractor is road-registered. If someone other than you is handing over, make sure they know the driver is coming and have the keys ready. For exports, the tractor must be free of soil and plant debris before it reaches the port, because plant health rules apply to used agricultural machinery, so wash it down thoroughly, including the wheel arches and underside.

Take dated photographs of the tractor from all sides before loading. If anything is damaged in transit, those photos make any claim straightforward.

Vintage and restoration tractors

Older tractors need extra care. Many vintage machines have weak handbrakes, worn steering boxes and no cab, so the driver will usually winch them aboard gently even if they run. Brittle wings, lights and seat pans can crack under a strap, so the tractor is secured by the axles and frame only.

Tell us if the tractor has original paint, a fresh restoration or show-standard finish. We can arrange covered transport or soft straps and padding where needed. For shows and rallies, give the arrival window and the gate the organisers want lorries to use, because show fields often have tight entry times on the morning.

If the tractor has been stood for years, check the tyres hold air and the wheels turn. Flat or perished tyres make loading much harder, and seized brakes may mean it has to be lifted rather than rolled.

Questions people also ask

Should I drain the fuel before a tractor is transported?

No. Leave enough fuel to drive the tractor on and off the trailer safely. A near-empty tank risks the engine stopping on the ramps. There is no need to fill it, and for some export shipments the shipping line may set a maximum fuel level, which we will tell you about.

Do I need to be there when my tractor is collected?

Not always, but someone needs to hand over the keys, confirm the right machine and show the driver the loading point. If you cannot be there, arrange for a neighbour, dealer or auction staff member to meet the driver, and tell us their name when booking.

Can you move a tractor that doesn't run?

Yes. Non-runners are loaded with a winch, and the trailer needs space for the winch line and enough room to steer the tractor straight. Tell us when booking whether the wheels turn and the steering works, because a seized machine may need lifting instead of winching.

Written and checked by the Farm Machinery Transport team. Read our editorial policy.

Get a free farm machinery transport quote

Tell us what you need and we'll come back with a clear price.

Request a quote